Description
The AC-EX40-444-KIT-SEA is the weatherpoof version of the AC-EX40-444-KIT.
Protecting delicate electronics with Sealoc’s nano-coating solution creates a virtually invisible, durable, waterproofing protective layer that works primarily with AVPro Edge’s own computer boards and components. The nano-coating creates a formidable barrier on circuitry that encapsulates the electronic components, protecting against water, moisture, humidity, dust, salt-air, and corrosion of various types.
The team at Sealoc does more than coat our extenders and decoders with their magic liquid. They also ensured the chassis were sealed correctly with extensive testing:
- Testing the overarching effectiveness of Sealoc’s Nano Fluid Treatment
- Testing on the Receiver units was done as hybrid applications meaning outdoor, covered, and in full direct rain situations. Testing for environments with heat, humidity, salt fog, rainfall, and more
- Rated IP68
The rainfall testing had the most significant impact on the functionality of the units. All control units failed immediately when the water was turned on.
A significant portion of protection is a coating made from a nanofluid developed explicitly for electronic boards by Sealoc. Ensure you have the tools to extend the life of installations in harsher conditions.
Tab Title
Downscaling: Scaling circuitry in the transmitter can step down 4K (including HDR metadata) to 1080p for legacy displays, especially useful in mixed resolution systems where native signal resolution is preserved for optimum performance system-wide.
EDID Management: Interoperability issues between displays and problematic AVRs or sources are easily resolved with EDID options available on the kit. EDID bypass and EDID copy simplify troubleshooting.
Distance Capabilities: Transmission distance varies by resolution bandwidth. HD 1080P signals can be sent 70 meters (230’) while 4K resolutions reliably reach 40 meters (115’). For new construction or whenever possible, shielded CAT6A is recommended.
Audio Extraction: Always active on both kit ends, PCM 2 Channel L/R Audio can be extracted from Phoenix connectors and sent to an AVR or distribution amplifier. NOTE: These ports only work if the source is set to output 2 Channel Audio. If down-mixing is required, please see the AVPro Edge AC-AVDM-AUHD. On-board Troubleshooting: Leave your Fox & Hound test kit behind in the shop? The AC-EX40-444-KIT has you covered. When required, the transmitter can generate a 1080P or 4K test pattern to aid with wire verification, switcher configuration settings, or source viability.
Control Options: Configurable, bidirectional control for IR & RS-232 signals provides a carefully nuanced added plus to the AC-EX40-444-KIT, consolidating wiring to a solitary pull and mitigating the use of supplemental devices for a clean, efficient installation. Simplified control requirements can take advantage of the AC-EX40-444-KIT’s I-PASS, forwarding commands directly from a control system IR-out port into the TX unit I-PASS input, proceeding to the receiving end and routing directly from the RX unit’s IR-out into the display’s IR input jack (if equipped) or through an attached IR emitter. ESD (electrostatic discharge) protection adds a welcomed layer of defense for all connected products.
Power Requirements: Power over HDBaseT (PoH) allows both devices to be fully powered from a user-selectable, single unit. The individual chassis of the AC-EX40-444-KIT are approximately cell phone-dimensioned, making placement options unlimited. Typical applications find the RX unit mated to the rear, jack panel area of the display with the TX unit and power supply positioned at the source end.
| Video: | |
| Video Resolutions | Up to 4K 60Hz 4:4:4 |
| VESA Resolutions | Up to DCI 4K (4096×2160) |
| HDR Formats | HDR10, HDR10+, HDG, Dolby Vision, Low Latency Dolby Vision |
| Color Space | YUV (Component), RGB (CSC: Rec. 601, Rec. 709, BT2020, DCI, P3 D6500) |
| Chroma Subsampling | 4:4:4, 4:2:2, 4:2:0 Supported |
| Color Bit Depth | Up to 16 bit (1080), Up to 12 bit (4K) |
| Down Scaling | 4K (and HDR) down to 2K |
| Audio: | |
| Audio Formats Supported HDMI | PCM 2.0 Ch, LPCM 5.1 & 7.1, Dolby Digital, DTS 5.1, Dolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio, DTS-X, Dolby Atmos |
| Audio Formats Supported Extracted (2CH) | PCM 2 Ch (No Downmix) |
| Distance: | |
| HDBaseT (CAT) Distance (4K) | 40 Meters / 131 Feet (Cat 6a) |
| HDBaseT (CAT) Distance (Full HD) | 70 Meters / 230 Feet (Cat 6a) |
| HDMI Lead In/Out (4K60 4:4:4) | Up to 50 Feet (using Bullet Train HDMI) |
| HDMI Lead In/Out (w/ AOC Cable) (4K60 4:4:4) | Up to 130 Feet (using Bullet Train AOC) |
| Other: | |
| Bandwidth | 18 Gbps (W/ ICT) |
| HDCP | HDCP 2.3 and Earlier |
| Ports: | |
| HDMI (TX & RX) | Type A |
| Audio (Extracted Analog) | 3 pin terminal block (Unbalanced) |
| IR TX (TX & RX) | 3.5mm Mono (2 Conductor) |
| IR RX (TX & RX) | 3.5mm Stereo (3 Conductor) |
| RS232 (TX & RX) | 3-pin terminal block |
| Power (TX & RX) | 2-Pin Terminal Block |
| Environmental: | |
| Operating Temperature | 23 to 125°F (-5 to 51°C) |
| Storage Temperature | -4 to 140°F (-20 to 60°C) |
| Humidity Range | 5-90% RH (No Condensation) |
| Power: | |
| Power Consumption (Total) | 12 Watts Max |
| Power Supply – Matrix | Input: AC 100-240V ~ 50/60Hz Output: DC 48V 0.5A |
| Dimensions: | |
| Dimensions (Single Unit Only, TX/RX are Same) (Height/Depth/Width) (TX/RX Each Alone) | mm: 129 x 92 x 12 inch: 5.05 x 3.62 x 0.47 |
| Dimensions (Packaged Height/Depth/Width) (Kit) | mm: 203 x 165 x 91 inch: 8 x 6.5 x 3.6 |
| Weight (Unit) (TX or RX Each Only) | 0.3 lbs (0.13 kg) |
| Weight (Packaged) | 2 lbs (0.90 kg) |
| *Specifications subject to change without notice. Mass & dimensions are approximate | |
- AC-EX40-444-T2 (Transmitter)
- AC-EX40-444-R (Receiver)
- 48V 0.5A Power Supply (One supplied)
- 1 x IR Tx Unit
- 1 x IR Rx Unit
- 4 x 3 Pin Terminal blocks for Audio and RS232 Ports
- 4 x Mounting Brackets
- 8 x Screws for Mounting Brackets
*Optional 3Pin to Stereo Audio Cables available for purchase
Đánh giá
Chưa có đánh giá nào.